LORD (OIL RESISTANT) TWO-PIECE RUBBER MOUNT | CB-2200 SERIES

Part # CB-2201-11

LORD (OIL RESISTANT) CB-2200 Series Two-Piece Rubber Mounts are designed for applications involving severe dynamic forces in both the static load direction and the rebound direction. Travel in both directions is limited by rubber compression, which provides snubbing.

Additional Images

Rubber-Parts-Catalog-com-LORD-Corporation-Two-Piece-Center-Bonded-Mount-CB-2200-Series-OIL-RESISTANT-CB-2201-11 Rubber-Parts-Catalog-com-LORD-Corporation-Two-Piece-Center-Bonded-Mount-CB-2200-Series-OIL-RESISTANT-CB-2201-11 Rubber-Parts-Catalog-com-LORD-Corporation-Two-Piece-Center-Bonded-Mount-CB-2200-Series-OIL-RESISTANT-CB-2201-11 Rubber-Parts-Catalog-com-LORD-Corporation-Two-Piece-Center-Bonded-Mount-CB-2200-Series-OIL-RESISTANT-CB-2201-11
Lets Get Started!  

Quick Quote
Ask A Question
Engineering Support

T - Thick Support Plate (Thickness - T) 0.375 in / 9.5 mm
Load/Deflection 40 lbs at 0.05 in / 178 N at 1.3 mm
T - Thin Support Plate (Thickness - T) 0.375 in / 9.5 mm
Load/Deflection 40 lbs at 0.05 in / 178 N at 1.3 mm
Elastomer OR - Oil Resistant Elastomer - Neoprene
Bolt Size 3/8" / M10
Bolt Grade or Class 5 SAE J429 / 5.8 SAE J1199
Part No. CB-2201-11 | CB220111
Washer Part Number J-2049-89
Manufacturer LORD Corporation
Part Category Vibration Control
Part Section Two-Piece Mounts
Part Type CB-2200 Series
Part Status
Call +1 800 657-0747 or use the
webform to the right on this page
Part Alternative
Call +1 800 657-0747  or use the
webform to the right on this page

 

Catalog Page No.
Catalog Section Page No.
Rubber Parts Catalog Two-Piece Mounts Page 8
LORD PC7000 Two-Piece Mounts Page 74
LORD PC2201m Two-Piece Mounts Page 68

 

 

Dimensions Technical Drawing
Dimension Measurement Note  
A 1.34/1.28 in / 33.3 mm  
B 0.407/0.396 in / 10.2 mm  
C 0.58 in / 14.7 mm Reference
D 1.28/1.22 in / 31.8 mm  
E 0.82/0.76 in / 20.1 mm  
F 0.515/0.455 in / 12.3 mm  
G 0.62/0.58 in / 15.2 mm  
H - Thick 0.44 in / 11.2 mm Thick Support Plate
H - Thin 0.44 in / 11.2 mm Thin Support Plate
SD 0.77/0.73 in / 19.1 mm  
R 0.04 in / 1.0 mm Reference
Bolt -  Size (English/Metric) 3/8" / M10  
Bolt - Grade or Class (SAE J429/J1199) 5 / 5.8 **
RubberPartsCatalog.com Delta-Flex-LORD-Two-Piece-Mounts-CB-2200-Series-figure.jpg

NOTES: Red figures are metric reference.

NOTE - * - For tightening torque information, refer to Tightening Torque Charts section.

 

***Notes only apply if called out in table***

NOTES

  1. These loads are for on-highway and general industrial applications. For off-highway, use 90% of the load shown.
  2. Installed dimensions are under no load
  3. Other parts available in the series, Contact Lord

 

 

 

Bolt Information - Table 2

For tightening torque information, refer to Tightening Torque Charts section.

Series No. RECOMMENDED BOLT INFORMATION*

CB-2201

SIZE
ENGLISH METRIC
3/8" M10
GRADE or CLASS
SAE J429 SAE J1199
5 5.8

 

 

 

 

Snubbing Washers - Table 3

Snubbing washers provide an interlocking system of metal parts which act to prevent damage from overload or excessive shock impact.  Steel washers are plated.

Series No. Washer Part No. O.D I.D. Thickness

CB-2201

J-2049-89 1.56 in. (39.6 mm) 0.391 in. (9.9 mm) 0.09 in. (2.3 mm)

 

 

 

 

Notes: Red figures are metric reference.

 

Features and Benefits

  • Dynamically effective in all directions
  • Prevent mechanical transmission noise
  • Accomodares misalignment and distortion
  • High rebound capacity
  • Easy to install with common tools
  • Standard bolt torque assures proper assembly
  • Top and bottom parts are alike, cannot be misassembled
  • Fail-safe assembly
  • Sized for English and Metric bolts
  • Long dependable service life
  • Economical

NOTE - *

For tightening torque information, refer to Tightening Torque Charts section.

NOTES

  1. Red figures are metric reference.

Custom Designs

Customized designs and special elastomer compounds for specific problems are available. These may result in spring rates and dimensions other than shown.

A part’s listing on this website does not guarantee its availability.

 

 

 

Custom Parts

Our custom molding department can make a part just for your application.

Engineering

Would you like some assistance in selecting the right mount for your application?  Our engineering department can help.  Please call or use the webform below.  We will be glad to assist.

Not what you are looking for?

Our knowledgeable staff can assist you with whatever you need.  From Special Packaging, Overnight shipments to applications engineering. DeltaFlex is ready to help find a solution.

Engineering Assistance

"Frequently vibration isolation problems require a system engineering analysis..." - Put us to work for you.

DeltaFlex has the computer capability, as well as specialized programs, for analyzing engine/transmission combinations. The output from these analyses is a mounting proposal which optimizes performance over the complete range of operating speeds. This service is available to you upon request. If you require this type of engineering assistance please call 800.657.0747 we will be glad to assist you.

What is the impact of Vibration Control?

The biggest impact that vibration isolation can have, is with the end users of our customers products, more importantly their perception of the quality of those products.

Values states herein represent typical values as not all test are run on each lot produced. For formalized product specifications or specific product end uses, contact Customer Service 262.632.2345.

A part’s listing on this website does not guarantee its availability.